Applied in 3 steps
Apply Elabrick adhesive mortar to the (pre-treated) surface.
Press Elabrick Brick Slips into the moist adhesive in the desired arrangement.
Smooth the seams using a slightly damp brush.
Application in
no time
Elabrick is the smart brick system that allows you to easily create your own atmosphere. The application of the brick slips on the inner wall or outer wall is quick and easy. Partly due to its low thickness of 3 to 4 mm, almost any solid surface is suitable for the Elabrick Brick Slip. Specific conditions regarding the surface are stated in the Application Instructions.
It’s as simple as that
Elabrick is a very simple, self-applied system. Watch the instructional video and get to work.
Suitable for any solid surface
A major advantage of Elabrick Brick Slips is that they are only 4 mm thick. That makes it possible to use them on almost any solid surface. This surface must be fl at, clean, dry, slightly absorbent, free of strain, and supportive. Examples of suitable exterior surfaces include facade insulation systems, render, stucco or cementitious board, and for interiors a wallpaper-ready wall or plasterboard. If the surface allows moisture to penetrate or is made of wood or bitumen, it is not suitable. When in doubt, always seek advice and do a test beforehand.
| Surface | Outdoor application | Indoor application |
| Wallpaper-ready wall | n.a. | yes |
| Decorative plaster | yes1 | yes1 |
| Sheet material, wood | no | no |
| Sheet material, plaster | no | yes2 |
| Sheet material, cement bonded | yes2+3 | yes2 |
| Plaster plate | yes2+3 | yes2 |
| Concrete, sand-lime brick, renovation plastering | yes4 | yes1 |
| Brick | yes1 | yes1 |
| Facade insulation system | yes | yes |
| Bitumen, tarry surface | no | no |
| Very porous surfaces | no | no |
| Damp surfaces | no | no |
1 provided the surface is level
2 follow the supplier’s instructions regarding transition of board seams to prevent cracking
3 if suitable for outdoor use
4 provided the surface is pre-treated and leveled
Solid exterior substrates
The Elabrick system can be used on almost any solid, permanently dry, load-bearing and stress-free substrate. Not suitable are moisture-permeable, sandy, porous, wooden and bituminous substrates. Highly absorbent substrates must be pre-treated with Elabrick Primer. Check beforehand for evenness, sufficient curing and, in case of outdoor application, sufficient weather protection during application and curing.
Exterior wall insulation
- Exterior wall
- Adhesive coat
- Insulation
- Basecoat and reinforcement mesh
- Elabrick Adhesive mortar
- Elabrick Brick slips
Prefab façade
- Façade element
- Insulation
- Plasterboard or cementitious board
- Basecoat and reinforcement mesh (system-dependent)
- Elabrick Adhesive mortar
- Elabrick Brick slips
Ventilated façade
- Exterior wall
- Sub-construction
- Plasterboard or cementitious board
- Basecoat and reinforcement mesh (system-dependent)
- Elabrick Adhesive mortar
- Elabrick Brick slips
Masonry
- Exterior wall
- Renovation/plastering
- Elabrick Adhesive mortar
- Elabrick Brick slips
Application Instructions also on paper
The Application Instructions are included in the packaging of the Elabrick Brick Slips and can also be downloaded below. Please read these instructions before you start your project.
Order online
Our website provides extensive information on the possibilities of Elabrick. For online orders, you will be redirected to one of our outlets.
Visit shop
You can also check out and buy Elabrick products at physical shops. Our partners will be happy to assist and advise you. You can easily locate the nearest DIY store.